JS230L Concrete Mixer-manufacture,factory,supplier from China

First. Handling of dustFrom the main station to the backyard dust to be solved, the main station adopts high efficiency pulse back-blowing active dust removal, plus large lantern dust removal, installation of mainstream fans to keep the air in the station fresh, powder tank using bin top dust removal and ground centralized dust collection, can also be concentrated on the batching layer platform dust collection, through the screw conveyor to the powder weighing, mixing station using pressurized spray unloading water to reduce the amount of dust in the mixer, the backyard encapsulated above

To prevent concrete mixer leakage, you could take the following steps:1. Regular protection: make sure to clean the mixer after every use, investigate and update any tired parts, tighten any free bolts, and lubricate the shifting parts.2. Use exquisite substances: use extremely good cement, sand, gravel, and water to make sure the concrete mix is homogeneous and that it flows easily thru the mixer.3. Avoid overloading the mixer: do now not overload the mixer past its capacity, as this could reason the mixer to leak.

There are several ways to prevent concrete mixer leakage:Check the seals: regularly check the seals of the concrete mixer, including the mixer dust sealing device, feeding system sealing device, discharge door sealing device and so on. Make sure the seals are in good condition and have no problems such as aging, wear or cracks.Clean the concrete residue: after each mixing of concrete, the interior and exterior of the concrete mixer should be cleaned in time.

The hazards of concrete mixer holding shaft1. Affect the quality of concrete, the mixer holding the shaft after hitting the concrete mixing is not uniform.2. Increase the load of the concrete mixer, energy consumption increases.3. Affect the wear parts, shaft seal life, accelerate the wear of wear parts, hold the shaft after the mixer arm wear is very serious, the service life is greatly shortened.Methods to prevent the mixer from holding the shaft1.

1.Maintain the body clean, remove the body of dirt and obstacles. 2.Check the oil, circuit and control equipment in each lubricating place, and fill the lubricating oil as required. 3.Before each shift, add water to the mixing drum and run idle for 1-2 minutes, and check the reliability of the clutch and the brake. 4.

Here are the steps to smooth a concrete mixer:1. Turn off the mixer: earlier than cleansing the concrete mixer, flip off the gadget and unplug it from the strength supply.2. Dispose of the cement: use a spade or shovel to do away with any last cement from the mixer. make sure to put on gloves and goggles to protect yourself from the cement dirt.3. Wash out the drum: fill the mixer with water to approximately halfway and flip it on. let it run for a couple of minutes to thoroughly wash out the drum. then, turn off the mixer and drain the water.4.

What equipment is generally available in a concrete mixing plantI. Mixing equipmentThat is, the general concrete mixer. At present, domestic manufacturers basically use double horizontal shaft forced concrete mixer, which has strong mixing function, uniform and rapid mixing, high productivity, and can achieve good mixing effect for dry hard, plastic and various proportion of concrete.　　Ⅱ. Weighing equipmentWeighing and batching equipment is an important piece of equipment in the concrete production process, which controls the ratio of various mixes.

Features of JS double horizontal shaft concrete mixer1. Compact structure: JS double horizontal shaft concrete mixer adopts vertical structure, covers a small area and has a compact structure.2. Uniform mixing: The equipment adopts double horizontal shaft design, which can mix various concrete ingredients quickly and evenly, ensuring stable and reliable concrete quality.3. Stable performance: JS double horizontal shaft concrete mixer adopts high-quality hydraulic and electrical components, stable performance and long service life.4.

  Commercial concrete mixing plant consists of mixing system, aggregate supply system, powder storage system, metering system, control system and external equipment.Mixing System  The mixing system is divided into forced mixing and self-falling mixing according to its mixing method. Forced mixer is the mainstream of mixing plant at home and abroad, which can mix various kinds of concrete such as fluidity, semi-dry hardness and dry hardness. The self-falling mixer mainly mixes liquid concrete and is rarely used in mixing plants.

Brief description of the start-up process of concrete mixing plant In a concrete mixing plant, the main mixing machine is an important part, which can be directly related to the output of the whole plant and the quality of the concrete produced. The normal start-up procedure of the mixing plant is crucial, the following is a brief introduction of how to start the mixing machine correctly.First, before starting the concrete mixer on, do a comprehensive inspection of the mixer.Second, start the mixing motor (i.e.